The most asking question by me. How to crack a gun safe with electronic lock? In all brands link Cannon, Liberty, Winchester, etc. The human memory can sometimes be unreliable that we forget the passcode or we enter a wrong passcode which would lead to the electronic mechanism of the weapon safe to fail.
There are times when someone would change the password without our knowledge. So, what can you do in this scenario? You would have to try and break your own gun safe. In this article, we talk about a few methods that will help in cracking a gun safe.
Table of Contents
Firstly, to do this we use a technique known as safe bouncing. It is an easy way to crack a gun safe such that even a kid could do it, but it is something that needs a bit of practice.
So, to do this you should drop the safe against the table or whatever surface it is placed on, and at the same time, you keep turning the knob of the safe. You have to get the timing right so that the turning of the knob matches with the brief moment of the safe’s lock bouncing open.
The above technique is great for safes that are in the lower end budget because only they tend to have locks that will lift. This will not work for safes that are on the expensive side as they have mechanisms that will hold the lock in place even when the safe is moving.
In this article, we will talk more in detail about the techniques that go behind in cracking the gun safe that is expensive and has an electronic lock. If you are interested in car gun safe read the review here: tickarise.com/car-gun-safe/
Can Magnets help in opening a Gun Safe?
To do this, we would need a rare earth magnet that is made out of neodymium. Remember that these are powerful and it can destroy your electronics and even lead to death or injuries if you’re not careful.
The science behind it is that gun safes mostly have a solenoid which is a coil with spring and pin. It is also known as a magnetic piece of hardware. The pin moves when the coil is energized due to the electronics of the keypad.
- Big neodymium Magnet
- The sock that is big enough to handle the magnet
- Get your safe ready that needs to be opened
So, after this take the magnet and put it into the sock. Then, take this and attach it to the gun safe. Since many of the cheap safes use nickel solenoids we need to locate the solenoid.
If it is a small safe, there isn’t much of a surface area, so place the magnet in the front door of the safe till you can open a safe. If the safe is bigger, then it will take some time before you can break open the safe. The reason why we need the sock is that these magnets are quite strong and having the sock makes it easier to move it around.
Next Method In Opening a Gun Safe
As we all know, electronic locks can be difficult to open as they have great security, but there are a few loopholes that we can use to crack open a gun safe with an electronic lock.
First, check the back or bottom of the gun safe for any bolt opening holes. Once you find these holes, use a flashlight to look through these small holes.
Find the electronic safe’s back panel and there should be a keypad and other buttons as well. Next, find a thin stick that will go through these holes. Use the wire or any other tool that will fit the hole and press the ‘reset’ button that is inside the keypad of the gun safe.
Then, make sure to add a new passcode that is simple and short to remember. Go ahead with pressing the ‘set’ button that will be next to the ‘reset’ button and then wait till a beep can be heard from the pad which signals that the new passcode is finalized.
Finally, try to open the safe using the new passcode and this will allow you to open the safe easily. Remember that if it doesn’t work it means you would have put a different code in the inner pad so repeat the steps again and set it upright.
Using current in opening a Gun Safe
The next technique is that when using an electronic lock, it has been found that you can find the correct code by observing the current that the lock consumes.
When you place the resistor in series along with the battery and lock and then observe the voltage of the resistor, we can understand the current that has been taken by the lock at any time.
So, the lock’s memory is matched with the input against the sequence of stored numbers and the current will waver depending on if the bit number that is stored is 0 or 1. By following this method, we can unravel the correct code which makes it relatively easy to open the lock.
Now, the above technique doesn’t work for all locks especially on gun safes that have a better electronic configuration and they are the best gun safe under 500. The technique of monitoring power consumption can backfire in this method.
It has been found that for locks like this, when a user inputs the code, there is a 28-microsecond delay and that if there were correct digits, there is a further delay that can be witnessed. So, being a patient can help in finding the correct code in cracking the safe.
There are a countless number of different techniques that can be used to unlock it with an electronic lock. The techniques that are mentioned in this article are the easiest way to unlock a gun safe. There are times when we could forget our own passcode and get frazzled on how to unlock the lock easily.
So, we hope that the techniques that have been highlighted in this article will help in unlocking your gun safe without causing much damage to the safe.